Accesso al pannello di amministrazione dell'eshop >> (Questo messaggio lo vedi solo tu!)
Ham Store Communications

OM4001A OM POWER

Amplificatore HF automatico 4000W

7.150,00
7.350,00

The advantages of OM4001A:

  • Full compatibility with

    • - ICOM
    • - YAESU
    • - ELECRAFT
    • - Ten-Tec Orion
    • - Kenwood
    • - Icom transceive protocol using by microHAM devices –CI-V output (MK II, MK2R, MK2R+, etc)
    • - Flex Radio Series 6xxx
    • - Apache Labs Anan
  • RF sensitive Band and Frequency switching, for use with radios which do not have CAT
  • Automatic switching between bands
  • Automatic tuning with the band according to segments
  • Automatic switching of band pass filter – BAND DATA output compatible with YAESU radios (BCD code)
  • Automatic switching of the antenna switches - maximum number of antennas is 10, controlled by BCD output code
  • Remote control via PC Windows Application

 

Specification of OM4001A:

Frequency coverage: Amateur Bands 1.8 – 29.7 MHz including WARC
Power output: 4000+ W in SSB and CW on HF bands,
3000W in RTTY and DIGI modes
Input Power: Usually 40 to 60W for full Output Power
Input Impedance: 50 Ohm, VSWR < 1.5 : 1
Power Gain: 17 dB
Output Impedance: 50 Ohm unbalanced
Maximum Output SWR: 3:1
SWR protection: Automatic switching to STBY, when reflected power is 350W or higher
Intermodulation distortion: -32dB below nominal output
Suppression of harmonics: < -50 dBc
Tubes: 2x FU728F Ceramic tetrode
Cooler: Centrifugal blower + Axial blower
Response speed of AUTO tune: less than 0,5s within same BAND ,less than 3s if out of BAND
Power supply: switchable 2 x 220/230/240V – 50 Hz one or two phases
Transformers: 2 pcs of toroidal transformer 3kVA
Dimensions: 485 x 200 x 455mm (width x height x depth)
Weight: 46 kg
Protection circuits: - VSWR too high
  - Anode current too high
  - Anode voltage error
  - Screen current too high
  - Screen voltage error
  - Grid current too high
  - Grid voltage error
  - Heating voltage error
  - Mistuning of PA
  - Temperature too high
  - Soft start for protecting your fuses
  - “switch-on blocking “ at opened amplifier
Indications: 4.3" colour touch screen display
Features: High level of protection
  Memory for faults and warnings, easy maintenance
  Automatic set-up anode current (BIAS) – no need to adjust manually after changing the tubes
  Three programmable working modes of the axial blower
  Full QSK with silent relay
  Many operational parameters to display
  The smallest and lightest 4000 W Power Amplifier on the market

LAN Connection

Power amplifier is interfaced to LAN via XPORT made by Lantronix (type XP1001000-05R). More info can be found at www.lantronix.com .

Default factory settings of XPORT are:

IP address: 192.168.1.222
Mask: 255.255.255.0
Gateway: 192.168.1.1

These are strictly default settings. You can modify any of these by going to XPORT web GUI via your web browser. We do not recommend changing any other parameters of the XPORT interface as loss of communication can be caused by doing so. There is no default user name or password. It is highly recommended to secure web interface with username and password.

For remote control and monitoring over LAN special software is needed. It is available free of charge, it can be downloaded from the following address:
https://www.om-power.com/download/HF4_PA_Manager_v3.25-setup.exe.

Continua lo shopping! scopri altri prodotti della sezione amplificatori hf o di OM Power